| ABSOLUTEEXTRUDER |
Convert file to absolute extrusion |
FALSE |
| ACCESSORYMODE_MAF |
Generate MAF file (accessory mode) |
FALSE |
| ACCESSORYMODE_MAFX |
Generate MAFX file (accessory mode) |
FALSE |
| ACCESSORYMODE_MSF |
Generate MSF file (accessory mode) |
FALSE |
| AFTERSIDEWIPEGCODE |
GCode line(s) to be executed after sidewipe sequence. Multiple AFTERSIDEWIPECODE lines can occur. They are inserted in the sequence they appear in the config block |
Empty |
| AUTOADDPURGE |
Automatically add purge to meet minsplice requirements (only with fullpurge reduction and sidewipe) |
FALSE |
| AUTOLOADINGOFFSET |
Unused? |
0 |
| BEDORIGINX |
X-position of the origin of the bed, since 5.1.0 taken from file, can be overridden |
Input file |
| BEDORIGINY |
Y-position of the origin of the bed, since 5.1.0 taken from file, can be overridden |
Input file |
| BEDSIZEX |
X-size of the bed, since 5.1.0 taken from file, can be overridden |
Input file |
| BEDSIZEY |
Y-size of the bed, since 5.1.0 taken from file, can be overridden |
Input file |
| BEFORESIDEWIPEGCODE |
GCode line(s) to be executed before sidewipe sequence. Multiple BEFORESIDEWIPECODE lines can occur. They are inserted in the sequence they appear in the config block |
Empty |
| BIGBRAIN3D_BLOBSIZE |
See BB3D section in this documentation |
40 |
| BIGBRAIN3D_BLOBSPEED |
See BB3D section in this documentation |
200 |
| BIGBRAIN3D_COOLINGTIME |
See BB3D section in this documentation |
12 |
| BIGBRAIN3D_ENABLE |
See BB3D section in this documentation |
FALSE |
| BIGBRAIN3D_FAN_OFF_PAUSE |
See BB3D section in this documentation |
0 |
| BIGBRAIN3D_LEFT_SIDE |
See BB3D section in this documentation |
FALSE |
| BIGBRAIN3D_MOTORPOWER_HIGH |
See BB3D section in this documentation |
450 |
| BIGBRAIN3D_MOTORPOWER_NORMAL |
See BB3D section in this documentation |
300 |
| BIGBRAIN3D_NUMBER_OF_WHACKS |
See BB3D section in this documentation |
1 |
| BIGBRAIN3D_RETRACT |
See BB3D section in this documentation |
3 |
| BIGBRAIN3D_PRIME_BLOBS |
See BB3D section in this documentation |
0 |
| BIGBRAIN3D_PURGEPOSITION |
See BB3D section in this documentation |
256.5 |
| BIGBRAIN3D_PURGEPOSITIONY |
See BB3D section in this documentation |
Empty |
| CHECKVERSION |
Check online for new version |
FALSE |
| CONSOLEWAIT |
Wait for user input at end of processing even if there are no errors |
FALSE |
| DEBUGTCOMMAND |
Do not use |
FALSE |
| DO_NOT_GENERATE_M0 |
Prevents M0 commands in the gcode. M0 is being interpreted by the Palette device as a pause |
FALSE |
| EXTRAENDFILAMENT |
Amount of extra filament added at the end of the print in the last used color (in mm) |
150 |
| FINISH_MOVES_M400 |
Replaces G4 P0 command to M400. This can be mandatory for some printer firmwares in order to clear there movement buffers and sychronize their motion to the pings of the Palette device |
FALSE |
| FULLPURGEREDUCTION |
Engages full purge reduction |
FALSE |
| IGNOREWARNINGS |
Closes P2PP after processing even if there were warnings |
FALSE |
| KLIPPER_TOOLCHANGE |
Detect KLIPPER TOOLCHANGE commands instead of default Tn commands |
FALSE |
| LINEARPINGLENGTH |
Sets the length between pings programmed in the file |
350 |
| MANUAL_SWAP |
Pauses the print with M25 on toolchange. This is commonly not used/set |
FALSE |
| MINSPLICE |
Minimal splice length |
70 |
| MINSTARTSPLICE |
Minimal first splice length |
100 |
| P3_HOSTNAME |
Hostname used to connect to the Palette 3 (Pro) for file uploading |
Empty |
| P3_MINIMALTOTALFILAMENT |
Define the minimum amount of total filament consumed in mm. This is commonly not used/set |
0 |
| P3_PROFILENAME |
Change the name of the printer in your splice file. It has no functional benefit to change this parameter |
Prusa Slicer - P2PP Output |
| P3_PROCESSPREHEAT |
Allows the Palette 3 (Pro) to preheat the printer. This only works in coneccted mode |
FALSE |
| P3_ROTATEINTERFACE |
Rotate the web interface of the Palette 3 (Pro) by 180 degrees |
FALSE |
| P3_SHOWPRINTERPAGE |
Show a web interface if the Palette 3 (Pro) |
FALSE |
| P3_UPLOADFILE |
Trigger for uploading your processed file to the Palette 3 (Pro) |
FALSE |
| P+LOADINGOFFSET |
Accessory mode parameter for Palette+ |
Empty |
| P+PPM |
Accessory mode parameter for Palette+ |
Empty |
| PALETTE3 |
Define your Palette device as a Palette 3 |
FALSE |
| PALETTE3_PRO |
Define your Palette device as a Palette 3 Pro |
FALSE |
| POWERCHAOS |
Special feature request to allow sub 300 mm pings |
FALSE |
| PRINTERPROFILE |
Printer profile string length 16 for P2 and before 32 bit for P3 |
50325050494e464f |
| PURGESPEEDADJUST |
Multiplier for the purge speed ranging between 10% and 500% [0.1 - 5.0] |
1.0 |
| PURGETOPSPEED |
Set speed limit during purging. Value <200 is interpreted as mm/sec, larger values are interpreted as mm/min |
Empty |
| PURGETOWERDELTA |
Engages power delta |
FALSE |
| SAVEUNPROCESSED |
Save a copy of the unprocessed file to disk (useful for debugging) |
FALSE |
| SIDEWIPECORRECTION |
Correction factor applied to the filament extruded during side wipe |
1 |
| SIDEWIPELOC |
See sidewiping section |
Empty |
| SIDEWIPEMAXY |
See sidewiping section |
175 |
| SIDEWIPEMINY |
See sidewiping section |
25 |
| SPLICEOFFSET |
Defines the extra length in mm added to the first splice |
30 |
| TEMPERATURECONTROL |
Enables active temperature control by introducing controlled temperature waits during the print to allow for cooldown/heatup matching the print higher/lower temp requirements |
FALSE |
| WIPEFEEDRATE |
Defines the default feedrate used for wiping |
3000 |